In Line Filters
Inline filters are used in hydraulic systems for separating solid materials from the hydraulic fluids and lubricating oils. They are intended for installation into pipelines.
Inline Filter with Filter Element according to DIN 24550
Type: 110 LE(N)
Size according to DIN 24550: 0040 to 0400
Size according to DIN 24550: 0040 to 0400
Additional sizes: 0130, 0150
Nominal pressure: 110 bar [1595 psi]
Maximum flow: 450 l/min
Connection: up to G 1 1/2; SAE 24
Operating temperature: -10 °C to 100 °C [14 °F to 212 °F]
Features:
They distinguish themselves by the following:
- Special highly efficient filter media
- Adsorption of very fine particles across a broad pressure differential range
- High dirt holding capacity thanks to large specific filter area
- Good chemical resistance of the filter elements
- High collapse resistance of the filter elements (e.g. in case of cold start)
- Filter ratings of 3 µm to 100 µm
- By default equipped with mechanical optical maintenance indicator with memory function
- Flow-optimized design due to 3D computer-supported design
Inline Filter with Filter Element according to DIN 24550
Type: 245 LE(N)
Size according to DIN 24550: 0040 to 0400
Additional sizes: 0130, 0150
Nominal pressure: 250 bar [3628 psi]
Maximum flow: 450 l/min
Connection: up to G 1 1/2; SAE 1 1/2; SAE 24
Operating temperature: -10 °C to 100 °C [14 °F to 212 °F]
Features:
They distinguish themselves by the following:
- Special highly efficient filter media
- Adsorption of very fine particles across a broad pressure differential range
- High dirt holding capacity thanks to large specific filter area
- Good chemical resistance of the filter elements
- High collapse resistance of the filter elements (e.g. in case of cold start)
- Filter ratings of 3 µm to 100 µm
- By default equipped with mechanical optical maintenance indicator with memory function
- Flow-optimized design due to 3D computer-supported design
Inline Filter with Filter Element according to DIN 24550
Type: 350 LE(N)
Size according to DIN 24550: 0040 to 1000
Additional sizes: 0130, 0150
Nominal pressure: 350 bar [5079 psi]
Maximum flow: 700 l/min
Connection: Up to G 2; SAE 2″; SAE 24
Operating temperature: -10 °C to 100 °C [14 °F to 212 °F]
Features:
They distinguish themselves by the following:
- Special highly efficient filter media
- Adsorption of very fine particles across a broad pressure differential range
- High dirt holding capacity thanks to large specific filter area
- Good chemical resistance of the filter elements
- High collapse resistance of the filter elements (e.g. in case of cold start)
- Filter ratings of 3 µm to 100 µm
- By default equipped with mechanical optical maintenance indicator with memory function
- Flow-optimized version due to 3D computer-supported design
Inline Filter with Filter Element according to DIN 24550
Type: 445 LEN
Size according to DIN 24550: 0040 to 0400
Nominal pressure: 450 bar [6527 psi]
Maximum flow: 700 l/min
Connection: Up to G 1 1/2; to SAE 2 1/2″; to SAE 24
Operating temperature: -10 °C to 100 °C [14 °F to 212 °F]
Features:
They distinguish themselves by the following:
- Special highly efficient filter media
- Adsorption of very fine particles across a broad pressure differential range
- High dirt holding capacity thanks to large specific filter area
- Good chemical resistance of the filter elements
- High collapse resistance of the filter elements (e.g. in case of cold start)
- Filter ratings of 3 μm to 100 μm
- By default equipped with mechanical optical maintenance indicator with memory function
- Flow-optimized version due to 3D computer-supported design
Inline Filter
Type: 40 FLE(N)
Nominal size according to DIN 24550: 0045 to 1000
Nominal sizes according to BRFS: 0045, 0055, 0120 to 270
Nominal pressure: 40 bar
Maximum flow: 2000 l/min
Connections: up to SAE 4″
Operating temperature: -10℃ to +100℃
Application:
- Filtration of pressure fluids and lubricants.
- Filtration of fluids and gases.
- Direct installation into pipe work.
- Direct wear protection of downstream components and systems.
- Offline filtration at high filter service lives.
Features:
- Filters for inline installation
- Particularly suited for off-line filtration
- Extremely large filter area
- Flow optimised design due to 3D computer-supported design
- Low pressure drop
- Special highly efficient filter media
Design:
Three part modular design comprising of lower filter part with inlet and outlet, mantel tube and removable threaded filter head.
Quality and Standardization:
The development, manufacture and assembly of BRFS industrial filters and BRFS filter elements is carried out within the framework of a certified quality management system in accordance with ISO 9001:2000.
The pressure filters for hydraulic applications according to 51401 are pressure holding equipment according to article 1, section 2.1.4 of the pressure equipment directive 97/23/EG (DGRL) However, on the basis of the exception in article 1, section 3.6 of the DGRL hydraulic filters are exempt from the DGRL, if they are not classified higher than category I (guideline 1/19). They do not receive a CE mark.
Inline Filter
Type: 100 FLE(N)
Nominal size according to DIN 24550: 0160 to 0630
Nominal sizes according to BRFS: 0045, 0055, 0120
Nominal pressure: 100 bar
Maximum flow: 1700 l/min
Connections: up to SAE 3″
Operating temperature: -10 ℃ to +100 ℃
Application:
- Filtration of pressure fluids and lubricants.
- Filtration of fluids and gases.
- Direct installation into pipe work.
- Direct wear protection of downstream components and systems.
- Offline filtration at high filter service lives.
Features:
- Filters for inline installation
- Particularly suited for off-line filtration
- Extremely large filter area
- Flow optimised design due to 3D computer-supported design
- Low pressure drop
- Special highly efficient filter media
Design:
Two-part design of filter housing with inlet and outlet as well as flange-mounted filter cover.
Quality and Standardization:
The development, manufacture and assembly of BRFS industrial filters and BRFS filter elements is carried out within the framework of a certified quality management system in accordance with ISO 9001:2000.
The pressure filters for hydraulic applications according to 51401 are pressure holding equipment according to article 1, section 2.1.4 of the pressure equipment directive 97/23/EG (DGRL) However, on the basis of the exception in article 1, section 3.6 of the DGRL hydraulic filters are exempt from the DGRL, if they are not classified higher than category I (guideline 1/19). They do not receive a CE mark.
Inline Filter
Type: 16 FE
Nominal sizes according to DIN 24550: 2500 to 7500
Nominal pressure: 16 bar
Connections: Up to DN 300
Operating temperature: -10 ℃ to +90 ℃
Application:
- Filtration of pressure fluids and lubricants.
- Filtration of fluids and gases.
- Direct installation into pipelines.
- Direct wear protection of downstream components and systems.
Features:
- Filters for inline installation
- Particularly suited for off-line filtration
- Extremely large filter area
- Flow-optimized design due to 3D computer-supported design
- Low pressure drop.
- Special highly efficient filter media
Design:
Steel welded construction of filter housing with connection for inlet and outlet positioned on the opposite side. Filter cover with bleed and filter housing with drain screws. Filter mounting by means of two welded on feet.
Quality and Standardization:
The development, manufacture and assembly of BRFS industrial filters and BRFS filter elements is carried out within the framework of a certified quality management system in accordance with ISO 9001:2000.
The pressure filters for hydraulic applications according to 51401 are pressure holding equipment according to article 1, section 2.1.4 of the pressure equipment directive 97/23/EG (DGRL) However, on the basis of the exception in article 1, section 3.6 of the DGRL hydraulic filters are exempt from the DGRL, if they are not classified higher than category I (guideline 1/19). They do not receive a CE mark.
Inline Filter with Filter Element according to DIN 24550
Type: 50 LE(N)
Size according to DIN 24550: 0040 to 0400
Additional sizes: 0130, 0150
Nominal pressure: 50 bar [725 psi]
Connection: Up to G 1 1/2; SAE 24
Operating temperature: -10 °C to 100 °C [14 °F to 212 °F]
Features:
They distinguish themselves by the following:
- Adsorption of very fine particles across a broad pressure differential range
- Good chemical resistance of the filter elements
- High collapse resistance of the filter elements (e.g. in case ofcold start)
- Filter ratings of 3 μm to 100 μm
- By default equipped with mechanical optical maintenance indicator with memory function
- Flow-optimized design due to 3D computer-supported design
Stainless Steel – Inline Filters
Type 40 EL, 100 EL, 450 EL
Size according to DIN 24550: 0004 to 0145
Nominal pressure: 690 bar
Connection: up to G 1 1/2; SAE 24
Operating temperature: -10 °C to 100 °C [14 °F to 212 °F]
Application:
Filtration of oil, water, waterbased fluids, agressive chemical liquids and gases. Direct installation in pipelines to provide wear protection of subsequent components and systems.
Design and Accessories:
High efficiency filter in stainless steel (1.4571). Optimised flow characteristics. Optional with bypass valve and maintenance indicator.
Advantages:
- One design for a wide range of working pressure, flow rate, temperature and applications.
- High reliability; there is only one filter design to maintain.
- For the design of a system: For the same flow rate in all pressure ranges the same connection and orientation.
- Less filter types in a system.
- The same filter element at same flow rates for all types. Less stock keeping of spare elements.
- Standard is an axial sealing (Type 40/100 EL…). Thereby a low dead storage design.
- The fluid is less time in the filter.
- Less corners and edges where the fluid can settle.
- Standard is an axial sealing (Type 40/100 EL…). This enables a huge range of temperatureand fluid resistant sealing materials.
- Possible temperature range -60°C and +200°C and possible applications for a wide amount of different fluids.
- To modify the sealing (Type 450 EL…) from radial to axial is possible at any time.
- Wide range of applications in various fluid and temperature ranges without change of the housing. By using for example stainless steel-O-rings the temperature range is even higher (-200°C and +200°C).
- Special coated stainless steel thread.
- High pressure and temperature resistant in comparison to traditional coatings. Easy disassembly and assembly due to slide effect of the coating. Damaged coating can be renewed.
- Special design features and standard plug enables quick and complete drain of the filter body.
- Low fluid loss and high reliability due to controlled drain and recirculation.
- Filter bowl made of two pieces for the large filter sizes.
- The handling during the change of the filter element is much more easy
Stainless Steel – Inline Filters
Type 690 EL, 1000 EL
Size according to DIN 24550: 0004 to 0014
Nominal pressure: 690 bar